Restore Floor Finish
Prepared 06/09
Armstrong World Industries, Inc.
P.O. Box 3001
Lancaster, PA 17604
Technical Services:
1-877-276-7876, Option 2,3,3
MATERIAL DATA SAFETY SHEET
I. Product Identification
Name: Armstrong Restore, Floor
Finish
Description: Urethane Acrylic
Finish
II. DEPARTMENT OF TRANSPORTATION
INFORMATION
Shipping name: not classified.
Hazard Class: N/A.
ID#: N/A
Packing Inst.: N/A
DOT/IMO/IATA: N/A
EMERGENCY ONLY CONTACT: CHEM-TEL
1-800-255-3924
III. HMIS (0=minimal
hazard; 4=severe hazard)
Health = 1
Flammability = 0
Reactivity = 0
IV. PRODUCT CONTENT
This product contains N-methyl-2-Pyrrolidone
which is subject to the reporting requirements of Section 313 SARA Title III
and 40 CFR 372. All components are on TSCA Inventory. This product does
NOT contain asbestos.
V. HAZARDOUS INGREDIENTS
|
Chemical Identity; Common Name
|
C.A.S. No.
|
%
|
OSHA PEL
|
ACGIH TLV
|
|
N-Methyl-2-Pyrrolidone
|
870-50-4
|
1- 5
|
N/A
|
N/A
|
100 ppm* - recommended by supplier
VI. PHYSICAL DATA
APPEARANCE AND COLOR: White
liquid. ODOR: Mild odor. BOILING POINT (degrees F):
N/A. VAPOR PRESSURE: N/A. VAPOR DENSITY: Heavier than
air. SOLUBILITY IN WATER: Soluble. SPECIFIC GRAVITY: 1.02
PERCENT VOLATILE BY WEIGHT: N/A. EVAPORATION RATE: Slower than
butyl acetate. pH: N/A.
VII. FIRE AND EXPLOSION
HAZARD DATA
FLASH POINT (Method): >220°
F. FLAMMABILITY RANGE: N/A. AUTOIGNITION TEMPERATURE: N/A.
EXTINGUISHING MEDIA: Foam, carbon dioxide or dry chemical.
SPECIAL FIRE FIGHTING PROCEDURES: Protect fire fighters from breathing toxic
products of combustion by wearing self-contained breathing apparatus. UNUSUAL
FIRE AND EXPLOSION HAZARDS: Closed containers in a fire may rupture due to
pressure build-up; use water to cool containers to prevent this.
VIII. HEALTH HAZARD
DATA
PRIMARY ROUTE(S) OF ENTRY: Skin
contact, eye contact, inhalation. EYE CONTACT: Will cause
irritation to eyes. SKIN CONTACT: Will cause irritation to skin, prolonged
or repeated contact can cause moderate irritation if not promptly washed from skin.
INHALATION: Inhalation of vapor may cause headache, nausea, and dizziness.
CARCINOGENICITY: NTP: No. IARC Monographs: No. OSHA
Regulated: No. FIRST
AID PROCEDURES: EYES: Upon eye contact, flush with cool water for at
least 15 minutes. If irritation persists, seek medical attention. SKIN: Upon
skin contact, wash affected area with soap and water. Get medical
attention if symptoms persist. INHALATION: Remove to fresh air.
Refer to physician if irritation or symptoms persist. INGESTION: Do
not induce vomiting, call a physician immediately.
IX. REACTIVITY DATA
STABILITY: Stable under normal
storage conditions. INCOMPATIBILITY: None. HAZARDOUS DECOMPOSITION
PRODUCTS: Carbon monoxide, carbon dioxide. HAZARDOUS POLYMERIZATION:
Will not occur under normal conditions.
X. SPILL OR LEAK PROCEDURES
SPILLS: Remove sources of ignition.
Contain spill. Wear appropriate protective equipment during clean-up and ventilate
area. Absorb with an inert material, such as clay and remove to appropriate
waste area. WASTE DISPOSAL METHOD: Dispose of container and any unused
contents in accordance with Federal, State and Local Waste Disposal Regulations.
Do not flush unused contents or residue down drains. Do not reuse container.
XI. SPECIAL HANDLING
AND USE INFORMATION
VENTILATION: Use with adequate
ventilation. Use local exhaust to insure that vapor levels are below the lowest
component TLV. RESPIRATORY PROTECTION: Not normally needed, if there
is not adequate ventilation, use with a NIOSH approved vapor cartridge respirator.
SKIN AND EYE PROTECTION: It is always a good safety practice to avoid contact
with eyes and skin. If contact may occur, use chemical splash goggles
and latex or rubber gloves.
XII. SPECIAL PRECAUTIONS
PRECAUTIONS TO BE TAKEN IN HANDLING
AND STORAGE: Do not store in excessive heat above 120F. Keep
away from heat and flame. Keep container closed when not in use. KEEP
OUT OF REACH OF CHILDREN. OTHER PRECAUTIONS: None.
WORK SITE ENVIRONMENT: Initially there may be a potential adverse impact on
indoor air quality within the general work area during the installation process.
Therefore you should advise the building manager or other appropriate person that:
-
It will be necessary to establish
and maintain adequate ventilation of the work area, without causing the entry of
contaminants to other parts of building; and
-
Persons who are sensitive to odors
and/or chemicals should be advised to avoid the work area during this process.
The information presented herein is
supplied as a guide to those who handle or use this product. Safe work practices
must be employed when working with any materials. It is important that the
end user makes a determination regarding the adequacy of the safety procedures employed
during the use of this product.
N/A - not applicable or not available
N/K - none known or not known